■ 特點 FeAtUrs
◎ 流化床為圓形結構避免死角。
◎ 料斗設置攪拌,避免潮濕物料團聚及干燥時形成溝流。
◎ 采用翻傾卸料,方便迅速*,亦可按要求設計自動進出料系統。
◎ 密閉負壓操作,氣流經過過濾。
◎ 操作簡便,清洗方便,是符合gMP要求的理想設備。
◎ 干燥速度快,溫度均勻,每批干燥時間一般均在20-30分鐘。
◎ The structure of fluidization bed is round so as to avoid dead corner;
◎ Inside the hopper there is a stir in order to avoid agglomeration of raw material and forming canal of flow;
◎ the granule is discharged through the method of turning over. In this way it is very convenient. The discharging system can be designed as request too;
◎ It is operated at the conditions of negative pressure and seal. The air is filtered. ◎ therefore it is simple in operation and convenient in clean. It is an idea equipment that is in conformity with the requirement of GMP;
◎ the drying speed is fast and the temperature is uniform. In general the drying time is 20~30 minutes.
■ 原理 principle
◎ 空氣經加熱凈化后,由引風機從下部導入,穿過料斗的孔網板。在 工作室內,經攪拌和負壓作用形成流態化,水份快速蒸發后隨著排 氣帶走,物料快速干燥。
◎ Purified and heated air is immited from the bottom by fan and passed through the screen plate of hopper. In the work chamber, the state of fluidization is formed through stirring and negative pressure. the moisture is evaporated and removed rapidly and the raw material is dried quickly.
■ 技術參數 technicAl pArAMeters
項 目 | 機 型 | |||||||||
投 料 | kg | 60 | 100 | 120 | 150 | 200 | 300 | 500 | 1000 | |
風 機 | 風 量 | m3/h | 2361 | 3488 | 4000 | 4901 | 6032 | 7800 | 10800 | 15000 |
風 壓 | mmH2O | 594 | 533 | 533 | 679 | 787 | 950 | 950 | 1200 | |
功 率 | kw | 7.5 | 11 | 15 | 18.5 | 22 | 30 | 45 | 75 | |
攪 拌 功 率 | kw | 0.55 | 0.55 | 0.55 | 0.55 | 0.55 | 0.75 | 1.1 | 2.2 | |
攪 拌 轉 速 | rpm | 11 | ||||||||
蒸 氣 耗 量 | kg/h | 141 | 170 | 170 | 240 | 282 | 366 | 451 | 800 | |
操 作 時 間 | min | 15-30 | ||||||||
主機高度 | mm | 2700 | 2900 | 3000 | 3100 | 3300 | 3800 | 4200 | 5800 |