■ 原理 principle
◎ 沸騰干燥器是利用經過濾后的潔凈空氣，經熱交換器的對流換熱,使空氣溫度上升到一定值進入主機分風筒，經閥片分配進入沸騰器，濕物 料從加料器進入干燥器。由于風壓作用，物料在干燥器內形成沸騰狀態(tài)，使熱空氣與物料進行充分接觸，增強了傳熱傳質過程，在較短的時間 內促使物料中的水份蒸發(fā)分離。物料干燥后由排料口排出，廢氣由沸騰床頂部排出，經旋風除塵器和布袋除塵器回收固體粉料后排空。本設備 一般進行負壓操作。
◎ XF fluidization drier use clean air after filtrating,through heat exchange, make air temperature rise to a certain value into main machine, then through distributor of valve plate into fluidization, material from feeder enter into the drier, because of wind pressure, raw material from boiling state in drier, the wide contact between hot air and raw material, increasing the process of hot exchang, In short time, make water vaporizing, raw material is discharged from the outlet. exhaust gas discharged from the top of the fluidization bed, and discharged from cyclone separator, dust filter with cloth bag after reclaiming material, the machine is working in negative pressure.

■ 應用 ApplicAtion
◎ 適應于醫(yī)藥藥品、化工原料、食品、糧食加工、飼料的干燥作業(yè)。 如；原料藥、壓片顆粒、中藥沖劑、保健食品、飲料沖劑、玉米胚 芽、飼料、塑料樹脂、檸檬酸和其它粉粒狀物料的干燥除濕。適用物 料粒徑一般為0.1~6mm，*粒徑為0.5~3mm。
◎ used on medicines, chemical raw material, foodstuff, grain processing, feed and so on. For example, raw medicine, granular tablet, Chinese tranditional medicine, health foods, drinks,maize embryo, feed, plastic resin, citric acid and other powders. the suitable diameter of raw material is normally 0.1-0.6mm. the most applicable diameter of raw material will be 0.5-3mm.


■ 技術參數 technicAl pArAMeters

型號	床層面積 m2	干燥能力 Kg/h	風機功率 kw	風壓 pa	風量 m3/h	進風溫度 °C	物料溫度 °C	zui大能耗 J	占地面積 m2	干燥機加料形式
XF20A	0.5	20～25	11	5.5×103	3110	60～140	40～60	2.6	25	1、星形加料式 2、星形加料式和氣力輸送并用
XF20B	0.5	20～25	11	5.5×103	3110	60～140	40～60	2.6	20
XF30A	1.0	30～45	18.5	5.5×103	4370	60～140	40～60	5.2	35
XF50A	2.0	55～90	30	7.4×103	7540	60～140	40～60	10.4	45
注：干燥能力與物料性和固含量及熱風進出口溫度有關。

注： 一、進料方式有：1、星形加料。2、星形加料式和氣加輸送并用。3、皮帶輸送。4、用戶
             自定。
       二、可實現自動化生產。
       三、除以上型號外，可為用戶作特殊設計。 
       四、根據物料不同，風機功率亦不同。
Remark: 1.the feeding method has :1）Star feeding. 2）. Combining star feeding and air conveyor. 3）.Belt conveying. 4）.Decided by customer 
              2.Automatic production can be realized.
              3.Besides the model above mentioned,the special model can also be
                 designed and manufactured as request. 
              4.According different raw material, the power of fan will be different.